Month: May 2020

Solicitations for participation as Research Institution (RI) in Small Business Technology Transfer (STTR), Phase I

Posted on by alirafique in Uncategorized
Solicitations

 

Solicitations are invited from qualified US institutions to participate as partner Research Institution (RI) in a National Science Foundation Small Business Technology Transfer (STTR) proposal to be submitted for third quarter of 2020 (deadline September 3). A project pitch followed by invitation is first step of process. If recommended for an STTR Phase I award, the small business proposer will need to complete a Cooperative Research Agreement (CRA) between the small business and the research institution prior to award.

 

Small business

Eastern Engineering Solutions LLC is a startup established in Detroit, Michigan under Public Law 114-328 (SBIR/STTR Reauthorization Act of 2017). SBIR/STTR Policy Directive and the Code of Federal Regulations (13 CFR 121) with an aim to serve current, upcoming and emerging technological and engineering requirements of United States. Its primary areas of operation are;;
a) Human space flight
b) Fusion

Apply positively to undersigned to be considered in application.

 

Muhammad Musaddique Ali Rafique

M: 617 470 1145
E: info@easternengineering.org

Development of flying saucers

Posted on by alirafique in Uncategorized
1. Ultra high speed counter directive concentric discs.
2. Translation of circular motion into linear motion as a function of frequency.
3. Critical resonance frequency.
4. Gyroscopic effect.
5. Stabilization of gyroscopes.
6. Magnetic levitation.
7. Contactless friction free bearings.
8. Motion of air in above setup.
9. Its direction, entry and exit paths.
10. Centrifuge (> 90,000 rpm).
11. Flow separation as a function of density, heavier towards center (axel / shaftl), lighter away from it.
12. Generation of lift and drag from it.

Design of Space Shuttle Launch Pad(s)

Posted on by alirafique in Uncategorized
  1. Structural engineering of space shuttle launch pads, their system engineering and integration.
  2. Fixed service structure and rotating service structure based on frame, block or tubular design
  3. Structural design (load calculation, bending moment diagram, shear force diagram and calculations of amount of forces acting of different elements and sections)
  4. Thermal stress calculations
  5. Wind load calculations
  6. Electrical wiring and load calculations
  7. Lightening protection system
  8. Initial design / sketch, calculations, re-design / design wetting / verification, safety factors, optimization, detail design (DD) and final design.
  9. Bill of materials
  10. Joining and fastening mechanisms

Open position – Conference style meeting coordinator – remote only

Posted on by alirafique in Uncategorized
A purely temporary position is immediately available to join the organization to assist, arrange and manage day-to-day activities related to an upcoming event entitled “Bulk metallic glass matrix composites III” in Pittsburgh, Pennsylvania on Oct 5 -6, 2020. This is remote-only position available on yearly basis which is likely to continue.

Ideal candidate should have prior experience of working in a professional society such as ASME, IEEE, ASM, AWS, ASTM, ACM or MRS and have well developed skills to manage scientific content, data and research. Candidate should also have skills to manage time and pressure and meet extremely tight deadlines.

If interested, please send your updated CV and / or company profile with at least two academic / professional references to info@easternengineering.org with subject line “Bulk metallic glass matrix composites III – open position”.

This is paid position. Remuneration will be decided in accordance with Bureau of Labor Statistics and on basis of reputation, track record and experience of contracting firm / individual and subject to availability of funding.  An honorarium may also be provided upon successful organization and management of meeting. Applications from minorities, disabled, veterans and members of low income and underrepresented communities are highly encouraged.

Small businesses / Companies may also participate as vendors / sub contractors but are required to follow standard operating procedure established which is proposal submission, bidding, award and execution. Companies must be registered in US and must have valid Social Security Number / Individual Taxpayer Identification Number / Employer Identification Number, Data Universal Numbering System (D-U-N-S) number, Commercial and Government Entity (CAGE) Code and must be registered in System for Award Management prior application.

Disclaimer: Eastern Engineering Solutions LLC reserves the right to cancel this advertisement and position at any time without any reason and notice. In this case, no legal action may be possible.

Design of fuel tank, strapping / joining and dis-joining mechanism

Posted on by alirafique in Uncategorized
  1. Calculations of amount of thrust required to generate enough exhaust velocity for mass of assembly (orbiter + fuel tank) to surpass escape velocity to break from earth gravity.
  2. Amount of fuel required as a function of its rate of combustion based on design of main engines.
  3. Dimensioning fuel tank to contain above amount of fuel

 

Design of solid rocket booster

Posted on by alirafique in Uncategorized
  1. Additional or balance thrust required to achieve exhaust velocity to break escape velocity of gravity of earth
  2. Type of fuel, its burning mechanism, rate of combustion, generation of heat, its transfer and exit through nozzle to generate effective exhaust velocity.
  3. Dimensioning of solid rocket booster, its strapping and dis-joining mechanism.
  4. Calculations of deflection and shear stresses and bending moments in tube / shell as a result of thermal, mechanical, acoustic and atmospheric (air friction) stresses.
  5. Material selection and fabrication.

Design of Space Shuttle (Orbiter) main engine

Posted on by alirafique in Uncategorized

This will include

  1. Design of Combustion chamber
  2. Design of exhaust nozzle (including type – bell shape)
  3. Design of ignition system and re-design to eliminate to achieve self ignition
  4. Design of heat generation system
  5. Design of cooling system (regenerative cooling)
    1. Calculation of heat load required to produce a certain amount of thrust
    2. Calculation of exhaust velocity.
    3. Tubing distribution, sizing, assembly and manufacturing
  6. Design of sound water suppression system
    1. Amount of water (water load calculation) required from thrust or amount of heat generated as a result of combustion.
    2. Rate of heat (energy) transfer and value of exhaust velocity.
    3. Intensity of sound produced from burning of certain amount of fuel / second (Rate of combustion)
    4. Rate of flow of water required to suppress that sound wave(s)
    5. Pumping (Number, type and arrangement of pumps and motors required)
    6. Tubing (size and amount of tubes required)
    7. Valves (Type, size and number of valves required)
    8. Line diagrams
    9. Flow diagrams
    10. Skid or mounting structure (including type, size and number of structural elements (Channels (Cs), Is, Tees, Ls) and fastening mechanisms (nut, bolt, rivets or weld) calculations.
    11.  Control of systems (PLC or DCS)